Set-up bench
A new bar goes in at the wrong height, and the manual’s three checks depend on each other. Move the sliders the way you would move the parts and watch the readings. The order that works is the manual’s: crosshead, then core, then bar height.
What is real here and what is not
- From the manual: the two cap readings must match; the looper points must reach the needle center line at 3/32" rise; the eye must then be about 3/32" below the looper; and which part is moved for each.
- Assumed by me: that the crosshead shifts the two loopers in opposite senses and the core shifts both together. That is the simplest reading of “equalize” then “advance”, but the manual does not spell it out.
- Arbitrary: which way is plus on each slider, the 0.500" starting cap reading, and the bar’s stroke in the 3D view. On the machine, find the direction by a small trial movement.
If it does not sew right afterwards
Manual and catalog pages used
My machine
The manuals leave several things unsaid, and the 3D view guesses at them. Your machine has the answers. Write them down as you go; they are saved in this browser, appear on the printed checklist, and can be copied out.
Sources, and how far to trust this
How each statement is marked
Every paragraph in the guide carries one of three marks: Manual stated in a Reece document, with quotation marks around quoted words; Drawing read off the catalog’s exploded views; Mine my inference or ordinary fitting practice.
What was checked, and how
- Part numbers (65 lines, catalog pp. 18–21): read from the Reece Series 101 catalog and compared line by line with the AMF Reece S-101 Parts List sheets 3-19 and 3-21 (rev. 04/2003). They agree.
npm testre-checks every number against the catalog text. - Adjustment text: taken from the S-101 Parts and Service Manual 97.1000.0.003 (rev. 09/2004). I compared it by eye with the hand-lettered Sheets 9, 10, 11 and 12 of the older Series 101 Service Manual; the wording and dimensions are the same. Other sheets were not compared.
- One error found in the S-101 edition: its looper sheet says to first check “Sheet 11 and … Sheet 12”. The old manual says Sheet 9 and Sheet 10 (race line-up and equalizing), which is what is meant; in S-101 numbering those are 1-12 and 1-13.
- Rest of the catalog: all 170 pages were paged through for anything touching the needle bar. That turned up the tools page (gage 03-0279, threading wire 03-0020), the timing core, the needle guard on the looper carrier, the head cover, and the RdE plate. They are under Parts.
- Not used: the 1976 colour scan (no text layer; same sheets), and the ManualsLib copy (duplicate).
What no Reece document says
- How to remove and refit a needle bar. There is no such procedure. The order of work here is mine, built from the exploded views.
- Which way the bar withdraws, what shim 01-4081 controls, how many buttons there are, and how the vibrator block turns yoke movement into the needle’s sideways throw.
- How the NEEDLE BAR DEPTH and RISE edges of gage 03-0279 are used.
- Any dimension of these parts. Every size in the 3D view is an estimate, and so is which side each part faces: which face the flats and buttons are on, where the lever and vibrator yoke come in from, and the number of cap screws.
Service Sheet 12 Fig. 1 does show the yoke’s nut at the bottom of the yoke, which is where the 3D view puts it; the catalog’s arrow for nut 10-1016-2 lands higher up, so confirm on the machine.
Sheet numbers
The old manual numbers its sheets 1–28; the S-101 edition numbers the same sheets 1-4 onward. For every sheet cited here, S-101 page = old sheet + 3. The Trouble Digest uses the old numbers.
Not consulted
The Facebook group. It needs a logged-in member, so nothing here comes from it. Someone there who has changed a 101 needle bar could settle the open points above with one photo.
Differences from the earlier site
- 10-1027-1-050 is a screw (two of them), not a “clamping block”.
- The earlier “8-stage factory procedure” and the “.008" light slip” button figure are not in any of the manuals.
- Shims 01-4081 run .005"–.012"; nothing in the manuals ties them to button pressure.
- The needle guard the Digest refers to (10-4010-2) is on the looper carrier, not the needle bar plate.